锡石多金属硫化矿微波助磨试验研究

本文以广西某选矿厂锡石多金属硫化矿矿石为原料,研究了微波预处理对矿石磨矿产物粒度组成、磨矿动力学、破碎速率及磨机生产能力的影响。结果表明,微波预处理后,矿石在不同磨矿时间下的磨矿产物粒度均变细,-0.074mm粒级含量提高了4.41%~12.90%；微波预处理前后该矿石磨矿均符合一级磨矿动力学模型；微波预处理使矿石的破碎速率(S₁)值提高近57%,且磨机的生产能力得到了明显提升。因此,微波预处理可以降低矿石的强度,强化矿石的磨矿过程,是一种有效的降低磨矿能耗、提高磨矿效率的方法。     

Process noise covariance estimation via stochastic approximation

Kalman filtering for linear systems is known to provide the minimum variance estimation error, under the assumption that the model dynamics is known. While many system identification tools are available for computing the system matrices from experimental data, estimating the statistics of the output and process noises is still an open problem. Correlation-based approaches are very fast and sufficiently accurate, but there are typically restrictions on the number of noise covariance elements that can be estimated. On the other hand, maximum likelihood methods estimate all elements with high accuracy, but they are computationally expensive, and they require the use of external optimization solvers. In this paper, we propose an alternative solution, tailored for process noise covariance estimation and based on stochastic approximation and gradient-free optimization, that provides a good trade-off in terms of performance and computational load, and is also easy to implement. The effectiveness of the method as compared to the state of the art is shown on a number of recently proposed benchmark examples.     

车门内饰板优化分析及模具设计

利用CAE分析软件Moldex3D先找出整个设计是否存在缺陷,为了增加优化效率,采用田口实验设计法规划控制因子与配置。L9(34)直交表来求得成型条件的最佳化参数组别,观察结果并找出最佳成型条件,以降低成型后所发生的体积收缩率以及翘曲位移量。由S/N因子反应表可看出对于Z轴变形量在塑料温度209℃、保压时间11.025 s、冷却时间17.85 s时较优良。Z轴的翘曲从1.64 mm降低到1.04 mm,整体改善了36.5%,最终根据优化结果进行了模具设计。     

一款紧凑增强型可变阻抗电磁带隙结构

基于传统AI-EBG结构,提出了一种小尺寸的增强型电磁带隙结构,实现了从0.5~9.4 GHz的宽频带-40 dB噪声抑制深度,且下截止频率减少到数百MHz,可有效抑制多层PCB板间地弹噪声。文中同时研究了EBG结构在高速电路应用时的信号完整性问题,使用差分信号方案可改善信号完整性。     

Super-resolution spectral analysis and signal reconstruction of magnetic Barkhausen noise

An investigation was performed based on frequency domain analysis and reconstruction for the magnetic Barkhausen noise (MBN). The power spectrum density (PSD) of MBN was analyzed based on autoregressive (AR) model. The relations between PSD peaks and mechanical properties of high strength steel sheet were studied. The energy of low frequency signal components decreases as hardness increases, and increases as tensile stress increases. The energy of high frequency signal components increases as hardness increases, and decreases as tensile stress increases. After identification, the MBN signal was reconstructed by discrete Gabor expansion which remains desired signal components and removes undesired ones.     

基准信号的低相噪声长距离光纤传输设计

介绍了基准光传输设备的基本组成和原理,指出低相噪长距离光纤传输中的问题所在,并提供了解决问题的方法,即数模混合器件的选择及改进滤波器设计.     

Random-valued impulse noise removal using adaptive dual threshold median filter

Noise detection and its removal is very important in the image processing. Detection of noise is very crucial and significant in random valued impulse noise because it does not hamper the image pixels uniformly. This paper presents a novel and unique concept of adaptive dual threshold for the detection of random valued impulse noise along with simple median filter at noise removal stage. Simulation results shows that an efficient noise detection leads to a superior quality of de-noised image as compared to existing adaptive threshold based image de-noising techniques. Proposed threshold computation is based on averaging of pixel values of window which enhances the PSNR of our system as compared to existing median filter based image de-noising methods.     

Energy aspects and workpiece surface characteristics in ultrasonic-assisted cylindrical grinding of alumina–zirconia ceramics

Ultrasonic assisted grinding is a novel method for improving the grinding process of difficult-to-cut materials. In the present research a novel setup has been designed and manufactured for utilizing ultrasonic vibrations in external cylindrical grinding. The designed ultrasonic head vibrates a rotating workpiece in axial direction. An alumina–zirconia ceramic (AZ90) has been selected as the workpiece material. Energy aspects and workpiece surface characteristics of ultrasonic assisted cylindrical grinding (UACG) and conventional cylindrical grinding (CG) processes have been analytically modeled and corresponding grinding experiments have been performed. The combined kinematics of the cylindrical plunge grinding process and axial ultrasonic vibrations provide a unique surface treatment conditions, which leads to reduced peak heights and increased valley depths of the surface topography. The main axial vibration mode provides the overlap of the adjacent cutting traces and consequently smoothens the surface topography in cylindrical plunge grinding. It has been analytically and experimentally shown that, applying ultrasonic vibrations, grinding energy can be reduced up to more than 35% depending on the process parameters. The surface characteristics of the ground workpieces have been investigated in terms of four surface roughness parameters and the roundness error.     

Kernel-based fourth-order diffusion for image noise removal

The fourth-order partial differential equations have good performance on noise smoothing and edge preservation without creating blocky effects on smooth regions. However, for low signal-to-noise ratio images, the discrimination between edges and noise is a challenging problem. A novel kernel-based fourth-order diffusion is proposed in this paper. It introduces a kernelized gradient operator in the fourth-order diffusion process, which leads to more effective noise removal capability. Experiment results show that this method outperforms several previous anisotropic diffusion methods for noise removal and edge preservation.     

Unrelated toxin–antitoxin systems cooperate to induce persistence

Persisters are drug-tolerant bacteria that account for the majority of bacterial infections. They are not mutants, rather, they are slow-growing cells in an otherwise normally growing population. It is known that the frequency of persisters in a population is correlated with the number of toxin–antitoxin systems in the organism. Our previous work provided a mechanistic link between the two by showing how multiple toxin–antitoxin systems, which are present in nearly all bacteria, can cooperate to induce bistable toxin concentrations that result in a heterogeneous population of slow- and fast-growing cells. As such, the slow-growing persisters are a bet-hedging subpopulation maintained under normal conditions. For technical reasons, the model assumed that the kinetic parameters of the various toxin–antitoxin systems in the cell are identical, but experimental data indicate that they differ, sometimes dramatically. Thus, a critical question remains: whether toxin–antitoxin systems from the diverse families, often found together in a cell, with significantly different kinetics, can cooperate in a similar manner. Here, we characterize the interaction of toxin–antitoxin systems from many families that are unrelated and kinetically diverse, and identify the essential determinant for their cooperation. The generic architecture of toxin–antitoxin systems provides the potential for bistability, and our results show that even when they do not exhibit bistability alone, unrelated systems can be coupled by the growth rate to create a strongly bistable, hysteretic switch between normal (fast-growing) and persistent (slow-growing) states. Different combinations of kinetic parameters can produce similar toxic switching thresholds, and the proximity of the thresholds is the primary determinant of bistability. Stochastic fluctuations can spontaneously switch all of the toxin–antitoxin systems in a cell at once. The spontaneous switch creates a heterogeneous population of growing and non-growing cells, typical of persisters, that exist under normal conditions, rather than only as an induced response. The frequency of persisters in the population can be tuned for a particular environmental niche by mixing and matching unrelated systems via mutation, horizontal gene transfer and selection.